Skip to main content

5  Central Chilled Water Plants and Primary Heat Rejection

Volume II
Chilled Water Plant
Cooling Towers
TES
FWS

Technical-Commercial Overview: The Primary Facility Water System (FWS)

The structural composition of data center mechanical systems is dictated by rack thermal power density and ambient climate conditions (ASHRAE TC 9.9 2021; Budlong 2024). Across both high-capacity air-cooled halls and high-density liquid-cooled facilities, the primary Facility Water System (FWS) forms the bulk heat-rejection backbone (ASHRAE TC 9.9 2023; Reliability Engine 2024). The primary FWS circuit operates at lower supply temperatures and higher flow rates, utilizing heavy-wall carbon steel or ductile iron mains that link outdoor cooling towers, adiabatic fluid coolers, and water-cooled or air-cooled chillers to Computer Room Air Handlers (CRAHs) or the primary side of Coolant Distribution Units (CDUs) (ASHRAE TC 9.9 2023; LVI Associates 2025).

Table 5.1: Central Chilled Water Plant and Primary FWS Measurement Breakdown
Mechanical System Element Takeoff Measurement Unit Primary Material & Engineering Specifications Critical QS Inclusions & Cost Drivers
Water-Cooled Centrifugal Chillers Number (No.) / Capacity (TR or kW) Variable-speed centrifugal or magnetic-bearing compressors; R-134a, R-513A, or low-GWP HFO-1234ze refrigerants (ASHRAE TC 9.9 2021; LVI Associates 2025). Dual-power active ATS, active harmonic filters (\text{THDi} < 5\%), fast-restart UPS controls, witnessed FAT, and seismic spring isolator pads (LVI Associates 2025).
Cooling Towers / Adiabatic Coolers Number (No.) / Heat Rejection (kW) Induced draft, counter-flow/cross-flow; SS316L cold water basins; VFD-driven direct-drive EC fans (LVI Associates 2025). Variable-frequency drives, basin heaters/sweeper piping, automated biocide/scale chemical skids, and acoustic attenuation baffles (LVI Associates 2025).
Primary Chilled Water Mains (FWS) Linear Meter (m) by diameter Schedule 40 carbon steel (ASTM A53 / A106 Gr. B); butt-welded joints \ge 200\text{ mm}, roll-grooved joints < 200\text{ mm} (RICS 2021; Helonic 2024). Non-destructive testing (NDT radiograph/ultrasonic on 10\%\text{–}100\% of welds), hydrostatic testing to 1.5\times design pressure, chemical flushing, and closed-cell insulation with vapor barrier (RICS 2021; Helonic 2024).

5.1 Water-cooled and air-cooled centrifugal/magnetic-bearing chillers: Capacity measurement, equipment scheduling, and vibration isolation bases

Under RICS NRM2 Section 38 and CSI Division 23, chillers are enumerated individually (No.) by cooling capacity (\text{kW}_{\text{th}} or Tons of Refrigeration, \text{TR}), entering/leaving chilled water temperatures (e.g., 12^\circ\text{C}/18^\circ\text{C} or 18^\circ\text{C}/26^\circ\text{C} for elevated-temperature free-cooling loops), and design ambient conditions (RICS 2021; ASHRAE TC 9.9 2021).

  • GCC High-Ambient Derating (50^\circ\text{C}\text{ to }55^\circ\text{C}): In Saudi Arabia, UAE, Qatar, and Oman, air-cooled chillers must be selected and priced with high-ambient tropicalized condenser coils, oversized VFD EC fan decks, and anti-corrosion epoxy/e-coated fins (for coastal corrosion resistance) capable of delivering 100\% rated duty at 50^\circ\text{C} (122^\circ\text{F}) ambient dry-bulb without high-pressure trip (RTTR Engineering Group 2024; AECOM 2024).
  • Fast-Restart & Ride-Through Inclusions: The MEP-QS must ensure chiller unit rates include UPS-backed micro-processor control panels and rapid-restart VFD software capable of restoring 80\%\text{ to }100\% cooling capacity within 30 to 45 seconds of generator power transfer (Uptime Institute 2018; h2x Engineering 2024).

5.2 Heat rejection infrastructure: Open and closed-circuit cooling towers, dry coolers, and adiabatic fluid coolers

Heat rejection plant selection balances Power Usage Effectiveness (PUE) against Water Usage Effectiveness (WUE) (ASHRAE TC 9.9 2021; Aman Engineering 2024):

  • Open-Circuit Cooling Towers: Achieve lower approach temperatures to ambient wet-bulb (yielding lower PUE) but consume significant make-up water via evaporation, drift, and blowdown—a major commercial constraint in water-scarce GCC jurisdictions (AECOM 2024).
  • Adiabatic Fluid Coolers & Dry Coolers: Utilize dry finned-tube heat rejection during cooler months and pre-cool intake air via wetted adiabatic pads only during peak summer hours, cutting annual water consumption by 70\%\text{ to }90\% (ASHRAE TC 9.9 2021; LVI Associates 2025). The BOQ must separately quantify adiabatic pad replacement sets and UV/RO feed-water treatment skids (RICS 2021).

5.3 Primary, secondary, and tertiary hydronic pumping arrangements: Variable Primary Flow (VPF) headers, in-line circulators, and differential pressure sensors

Modern hyperscale chilled water plants favor Variable Primary Flow (VPF) or primary-secondary-tertiary pumping topologies (ASHRAE TC 9.9 2023; Reliability Engine 2024). Each pump skid is measured by flow rate (\text{L/s}), total dynamic head (\text{kPa} or \text{m H}_2\text{O}), motor kilowatt rating, and VFD enclosure IP rating, inclusive of inertia bases, suction diffusers, triple-duty check/balance valves, and remote differential pressure (\Delta P) transmitters wired in N+1 redundancy (RICS 2021).

5.4 Primary facility piping: Heavy-wall carbon steel, welded/grooved joints, valves, strainers, and balancing devices

In accordance with RICS NRM2, primary chilled water and condenser water pipework is measured in linear meters (m) along the centerline over all fittings, grouped by nominal diameter (\text{DN15} to \text{DN600+}) and pipe schedule (ASTM A53 / A106 Grade B Schedule 40) (RICS 2021). Extra-over (EO) item counts must be taken off for butt-welded elbows, tees, concentric/eccentric reducers, grooved couplings, PN16/PN25 lugged butterfly valves, motorized isolation valves (MOVs) for Tier III/IV loop isolation, and pressure-independent control valves (PICVs) (Uptime Institute 2018; RICS 2021; Helonic 2024).

5.5 Thermal Energy Storage (TES) systems: Stratified chilled water tanks, phase-change storage, and emergency ride-through quantification

During a utility blackout, standby generators require 10 to 30 seconds to synchronize and accept load, and chillers require an additional 30 to 90 seconds to ramp compressor capacity (Uptime Institute 2018; h2x Engineering 2024). To satisfy Uptime Tier III/IV continuous cooling mandates, the MEP-QS must quantify Thermal Energy Storage (TES) vessels (Uptime Institute 2018; h2x Engineering 2024):

V_{\text{TES (Liters)}} = \frac{Q_{\text{IT (kW)}} \times t_{\text{ride-through (s)}}}{\rho \cdot C_p \cdot \Delta T_{\text{chw}} \cdot \eta_{\text{stratification}}} \tag{5.1}

Pressurized steel buffer vessels (typically ASME Section VIII certified) or atmospheric stratified chilled water tanks (\eta_{\text{stratification}} \approx 0.85\text{–}0.90) must be measured complete with internal diffuser nozzles, external polyisocyanurate (PIR) insulation, aluminum cladding, and UPS-backed emergency discharge pumps (RICS 2021; h2x Engineering 2024).